Por favor, use este identificador para citar o enlazar este ítem: http://repositorio.utc.edu.ec/handle/27000/10352
Registro completo de metadatos
Campo DC Valor Lengua/Idioma
dc.contributor.advisorPorras Reyes Jefferson Alberto-
dc.contributor.authorChavez Bunshe, José Luis-
dc.contributor.authorToctaguano German, Andy Santiago-
dc.date.accessioned2023-06-09T14:38:55Z-
dc.date.available2023-06-09T14:38:55Z-
dc.date.issued2023-
dc.identifier.citationChavez Bunshe José Luis, Toctaguano German Andy Santiago (2023); Diseño y construcción de un banco de pruebas para el análisis de variables eléctricas en cargas desbalanceadas. UTC. Latacunga. 147 p.es_ES
dc.identifier.otherPI-002438-
dc.identifier.urihttp://repositorio.utc.edu.ec/handle/27000/10352-
dc.descriptionIn the present technological proposal, the data and electrical signals in unbalanced loads within a three-phase electrical system are analyzed, which allows visualizing the offset of the sine and phasor waves of the voltage with respect to the current when activating the load L, RL and RLC. For this, a protection system was implemented for the different loads, with TC's and TP's sensors that are constituted in the PZEM (1:6 A), which works as a signal conditioning, which sends a serial signal to the Arduino UNO, to the PLC S7 - 1200 by TCP IP communication and to LabVIEW by the open server via Ethernet with the creation of a graphical interface, the module has 6 digital outputs to activate the 4 inductive, resistive and capacitive loads and 4 manual outputs for the 4 inductive loads, managing to measure and observe in a real way the behavior of the electrical variables in each of its three-phase phases, the unbalanced system shown in the module is due to the resistive load, which is achieved obtain the highest current of a line allowing to visualize the sinusoidal waves of the RMS voltage and the peak current of the system.es_ES
dc.description.abstractEn la presenta propuesta tecnológica se analiza los datos y señales eléctricas en cargas desbalanceadas dentro de un sistema eléctrico trifásico, que permite visualizar el desface de las ondas senoidales y fasoriales de la tensión con respecto a la corriente al activar la carga L, RL y RLC, para ello se implementó un sistema de protecciones para las diferentes cargas, con sensores de TC´s y TP´s que están constituidos en el PZEM (1:6 A), mismo que trabaja como un acondicionamiento de señales, el cual, manda una señal serial al Arduino UNO, al PLC S7 – 1200 por una comunicación TCP IP y a LabVIEW por el open server mediante Ethernet con la creación de una interfaz gráfica, el módulo consta con 6 salidas digitales para activar las 4 cargas inductivas, resistiva y capacitiva y 4 salidas manuales para las 4 cargas inductivas, logrando medir y observar de manera real el comportamiento de las variables eléctricas en cada una de sus fases trifásicas, el sistema desbalanceado que se muestra en el módulo es debido a la carga resistiva, mismo que se logra obtener la corriente mayor de una línea permitiendo visualizar las ondas senoidales del voltaje RMS y la corriente pico del sistema.es_ES
dc.format.extent147 páginases_ES
dc.language.isospaes_ES
dc.publisherEcuador : Latacunga: Universidad Técnica de Cotopaxi (UTC)es_ES
dc.rightsopenAccesses_ES
dc.rights.urihttp://creativecommons.org/licenses/by-nc-sa/3.0/ec/es_ES
dc.subjectDESBALANCEADASes_ES
dc.subjectREACTIVAes_ES
dc.subjectTRIFÁSICOes_ES
dc.subjectENERGÍAes_ES
dc.subject.otherELECTROMECÁNICAes_ES
dc.titleDiseño y construcción de un banco de pruebas para el análisis de variables eléctricas en cargas desbalanceadases_ES
dc.typebachelorThesises_ES
Aparece en las colecciones: Tesis - Ingeniería Eletromecánica

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
PI-002438.pdfPROYECTOS DE GRADO A TEXTO COMPLETO8,66 MBAdobe PDFVisualizar/Abrir


Los ítems de Repositorio UTC están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.