Por favor, use este identificador para citar o enlazar este ítem: http://repositorio.utc.edu.ec/handle/27000/5539
Registro completo de metadatos
Campo DC Valor Lengua/Idioma
dc.contributor.advisorCevallos Betún, Segundo Ángel, Ing. M.Sc.-
dc.contributor.authorGanán Paca, Paúl Israel-
dc.contributor.authorMullo Aimacaña, Alex Darío-
dc.date.accessioned2020-07-28T17:03:31Z-
dc.date.available2020-07-28T17:03:31Z-
dc.date.issued2019-07-
dc.identifier.citationPaúl Israel Ganán Paca Alex Darío Mullo Aimacaña (2019) Rediseño de una máquina de ensayos de torsión existente en los laboratorios de la Universidad Técnica De Cotopaxi para determinar el comportamiento mecánico de los materiales. UTC. Latacunga. 134 p.es_ES
dc.identifier.otherPI-001394-
dc.identifier.urihttp://repositorio.utc.edu.ec/handle/27000/5539-
dc.descriptionThe purpose of the present project was to redesign and implement a machine for torsion tests in the Materials Resistance Laboratory of the Electro-mechanic Career of the CIYA Faculty, which will allow the students of the Career to determine the mechanical properties of Different materials when subjected to a torque. For the redesign of this equipment, a machine used as a base that was in disuse because it did not have a data acquisition system. With this background, we proceeded to redesign this equipment through the implementation of a torque sensor. 100 Nm for the applied torque measurement, this sensor is connected to a signal conditioner for communication between the equipment and the data acquisition card DAQ 6008. With the sensor and an encoder installed in the machine, the programming designed so that the measured torque and angle of rotation were recorded and stored, allowing to graph the behavior of the material in real time until reaching the breaking point. The electrical and electronic connections installed on a control board. The specimens for the tests were prepared according to the ASTM E143 Standard and to check the reliability of the machine. It was carried out tests with the most used steel materials in the national industry such as: ASTM A36, SAE 1018, AISI 1045 and AISI 4340, then the relationship that exists between the found values found in the torsional yield stress and the tensile yield value indicated in the technical sheet of each steel tested. These relationships were the following: 1.39; 1.52; 1.51; 1.85 respectively; so it was concluded that the team is reliable in the results.es_ES
dc.description.abstractLa finalidad del presente proyecto fue el de rediseñar e implementar una máquina para ensayos de torsión en el laboratorio de Resistencia de Materiales de la Carrera de Electromecánica de la Facultad de CIYA, la misma que permitirá a los estudiantes de la Carrera determinar las propiedades mecánicas de distintos materiales cuando están sometidos a un par de torsión. Para el rediseño de este equipo se utilizó como base una máquina que se encontraba en desuso debido a que no contaba con un sistema de adquisición de datos, con estos antecedentes se procedió a rediseñar este equipo a través de la implementación de un sensor de torque de 100 N.m para la medición del par torsor aplicado, este sensor está conectado a un acondicionador de señal para la comunicación entre el equipo y la tarjeta de adquisición de datos DAQ 6008. Con el sensor y un encoder instalado en la máquina, se diseñó la programación para que el torque y el ángulo de giro medido se registren y almacenen, permitiendo graficar el comportamiento del material en tiempo real hasta llegar al punto de ruptura. Las conexiones eléctricas y electrónicas fueron instaladas en un tablero de control. Las probetas para los ensayos fueron elaboradas según la Norma ASTM E143-02 y para comprobar la fiabilidad de la máquina se procedió a realizar ensayos con los materiales de acero más utilizados en la industria nacional como son: ASTM A36, SAE 1018, AISI 1045 y AISI 4340, luego se determinó la relación que existe entre los valores hallados del esfuerzo de cedencia a torsión con el valor de cedencia a tracción que viene indicado en la hoja técnica de cada acero ensayado. Siendo estas relaciones las siguientes: 1,39; 1,52; 1,51; 1,85 respectivamente; por lo que se concluyó que el equipo es fiable en los resultados.es_ES
dc.format.extent134 páginases_ES
dc.language.isospaes_ES
dc.publisherEcuador: Latacunga: Universidad Técnica de Cotopaxi (UTC).es_ES
dc.rightsopenAccesses_ES
dc.rights.urihttp://creativecommons.org/licenses/by-nc-sa/3.0/ec/es_ES
dc.subjectMÁQUINA DE ENSAYOSes_ES
dc.subjectTORSIÓN EXISTENTEes_ES
dc.subjectLABORATORIOSes_ES
dc.subject.otherMECÁNICA INTEGRALes_ES
dc.titleRediseño de una máquina de ensayos de torsión existente en los laboratorios de la Universidad Técnica De Cotopaxi para determinar el comportamiento mecánico de los materiales.es_ES
dc.typebachelorThesises_ES
Aparece en las colecciones: Tesis - Ingeniería Eletromecánica

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
PI-001394.pdfPROYECTO DE GRADO A TEXTO COMPLETO8,87 MBAdobe PDFVisualizar/Abrir


Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons