Por favor, use este identificador para citar o enlazar este ítem: http://repositorio.utc.edu.ec/handle/27000/5602
Registro completo de metadatos
Campo DC Valor Lengua/Idioma
dc.contributor.advisorPesántez Palacios, Gabriel Napoleón, Ing. MSc.-
dc.contributor.authorCabezas Mayorga, Klever Santiago-
dc.date.accessioned2020-07-30T17:06:39Z-
dc.date.available2020-07-30T17:06:39Z-
dc.date.issued2018-08-
dc.identifier.citationCabezas Mayorga Klever Santiago (2019); Diseño de una malla de puesta a tierra; en un galpón de la fábrica Inplastico. UTC. Latacunga. 104 p.es_ES
dc.identifier.otherPI-000810-
dc.identifier.urihttp://repositorio.utc.edu.ec/handle/27000/5602-
dc.descriptionThe objective of this research project is to design a grounding mesh that channels fault overcurrent to safe reference points in order to avoid accidents to people and lengthen the useful life of the machinery that performs activities in the new warehouse. INPLASTIC factory, this activity will lead to the best performance of staff thus provides greater security when it comes to perform their daily tasks. Then, to perform a correct dimensioning of the grounding mesh in the new INPLASTICO factory ship, in the first instance soil resistivity must be measured since the design of the system will largely depend on this parameter. This activity is carried out with the help of an EXTECH 382152 tellurometer using the rod depth method, in the case of that the corresponding measure has a high value; suggestions can be made to increase its conductivity, thus reducing the cost of materials needed for future implementation. Consequently, the final resistance calculation is elaborated by scientific methods such as IEEE - 80 and those exposed by Laurent and Niemann, who have studied the geophysical and geoelectric phenomena of grounding. In addition, a short circuit study designed in the MELSHORT program sponsored by Mitsubishi is prepared based on the equipment that is to be installed in the new shed in order to obtain short-circuit values, the same ones that will allow to dimension the protections and calibers of conductors for each machine as well as the final caliber of the conductor that will be connected from lightning rods, measurement and protection boards, metal structure; to the ground mesh, preventing the flow of pitch and touch affects the staff who every day performs production activities, tooling, office and warehouse.es_ES
dc.description.abstractEl presente proyecto de investigación tiene como objetivo diseñar una malla de puesta a tierra que canalice sobrecorrientes de falla a lugares de referencia segura con el fin de evitar percances a personas y alargar la vida útil de la maquinaria que realizan actividades en el nuevo galpón de la fábrica INPLASTICO, esta actividad conllevará al mejor desempeño del personal pues se brinda mayor seguridad a la hora de realizar sus labores cotidianas. Para realizar un correcto dimensionamiento de la malla de puesta a tierra en la nueva nave de la fábrica INPLASTICO, en primera instancia se debe medir la resistividad del suelo ya que de este parámetro dependerá en gran parte el diseño del sistema. Esta actividad se la realiza con la ayuda de un telurómetro de marca EXTECH 382152 mediante el método de profundidad de varilla, en el caso de que la medida correspondiente presente un valor elevado se podrá realizar sugerencias para aumentar la conductividad del mismo logrando reducir el costo de materiales necesarios para la futura implementación. El cálculo de resistencia final se elabora mediante métodos científicos tales como IEEE – 80 y los expuestos por Laurent y Niemann, quienes han estudiado los fenómenos geofísicos y geoeléctricos de la puesta a tierra. Además se elabora un estudio de cortocircuitos diseñado en el programa MELSHORT patrocinado por Mitsubishi en función a los equipos que se pretende instalar en el nuevo galpón con el fin de obtener valores de cortocircuito, los mismos que permitirán dimensionar las protecciones y calibres de conductores para cada máquina así como también el calibre final del conductor que se conectará desde pararrayos, tableros de medición y protección, estructura metálica; hacia la malla de tierra, evitando que las corrientes de paso y de toque afecten al personal que día a día realiza actividades de producción, matricería, oficina y bodega.es_ES
dc.format.extent104 páginases_ES
dc.language.isospaes_ES
dc.publisherEcuador: Latacunga: Universidad Técnica de Cotopaxi (UTC).es_ES
dc.rightsopenAccesses_ES
dc.rights.urihttp://creativecommons.org/licenses/by-nc-sa/3.0/ec/es_ES
dc.subjectCORTOCIRCUITOes_ES
dc.subjectCONDUCTORESes_ES
dc.subjectRESISTIVIDADes_ES
dc.subjectSOBREVOLTAJESes_ES
dc.subject.otherSISTEMAS ELÉCTRICOSes_ES
dc.titleDiseño de una malla de puesta a tierra; en un galpón de la fábrica Inplastico.es_ES
dc.typebachelorThesises_ES
Aparece en las colecciones: Tesis - Ingeniería Eléctrica

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
PI-000810.pdfPROYECTO DE GRADO A TEXTO COMPLETO3,41 MBAdobe PDFVisualizar/Abrir


Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons