Por favor, use este identificador para citar o enlazar este ítem: http://repositorio.utc.edu.ec/handle/27000/6787
Tipo de Material: bachelorThesis
Título : Simulación del control de potencia activa y reactiva de un aerogenerador.
Autor : Freire Freire, Armando Salvador
Toapanta Rocha, Luis Miguel
Director de Tesis: Quinatoa, Carlos, MsC.
Descriptores: Eléctrica
Aerogenerador
Fecha de publicación : feb-2020
Ciudad: Editorial: Ecuador: Latacunga: Universidad Técnica de Cotopaxi; Facultad de Ciencias de la Ingeniería y A plicadas.
Citación : Freire Freire. A.S. (2020) Simulación del control de potencia activa y reactiva de un aerogenerador. U.T.C. Latacunga. 64 p.
metadata.dc.format.extent: 64 páginas
Resumen : En esta investigación, se mostró el análisis y control de la potencia activa y reactiva en el lado de la red de un aerogenerador, debido a las variaciones de la velocidad del viento, las variables de estado son fluctuantes y no se pueden acoplar a la barra infinita, para este problema se realizó una simulación mediante el software Simulink/ Matlab, se implementó un sistema de control capaz de solucionar estos inconvenientes. Para el desarrollo de la investigación se analizó la literatura científica y metodológica para determinar el estado de arte de las configuraciones y modelados de control utilizados en generadores eólicos. Como resultado se empleó la configuración tipo D, debido a que presenta una mayor eficiencia para el Sistema de Conversión de Energía Eólica (WECS), basado en una máquina síncrona de imanes permanente (PMSG) por accionamiento directo, un control back to back que cuenta con un rectificador e inversor accionado por IGBT´s, conectados a través de un condensador de corriente continua. El control de potencia activa se realizó por el lado del generador, por medio del máximo coeficiente de potencia, en el estudio realizado, se utilizó un control pitch angle, donde la máxima potencia entregada por la turbina se obtiene con un valor de betha de 0 grados. Mientras tanto el control de potencia reactiva, voltaje y frecuencia se hizo por el lado de la red, para lo cual se implementó diferentes tipos de controles, denominado control orientado de voltaje o COV, se procede a la transformación de Clarke y Park, tanto para voltajes y corrientes con valores CC en un sistema de referencia estacionario, cuenta también con un control PLL que mantiene el valor de ángulo de fase sincronizado con el voltaje de la red, además un control INNER LOOP capaz de variar las corrientes de salida del inversor y finalmente junto al control OUTER LOOP que entrega corrientes de referencia para controlar la potencia activa y reactiva a la red, demostrando la eficacia de la estrategia de control propuesta en teoría.
Descripción : In this research project, the analysis and control of the active and reactive power on the network side of an aerogenerator is showned, due to variations in wind speed, the state variables are fluctuating and cannot be coupled to the bar infinite, for this problem a simulation is performed using the Simulink / Matlab software, implemented a control system capable of solving these problems. For the development of the research project, the scientific and methodological literature is analyzed in order to determine the state of the art of the configurations and control models used in wind generators. As a result, the type D configuration is used, because it has a greater efficiency for the Wind Energy Conversion System (WECS), based on a permanent magnet synchronous gadget (PMSG) by direct drive, a back to back control that counts with a rectifier and inverter powered by IGBT´s, connected through a direct current capacitor. The active power control is carried out by the generator side, by means of the maximum power coefficient, in the study carried out a control pitch angle is used, where the maximum power delivered by the turbine is obtained with a betha value of 0 degrees. Meanwhile the control of reactive power, voltage and frequency is done on the network side, for which different types of controls, called voltage control oriented or VCO, both for voltages and currents with DC values in a stationary reference system, it also has a PLL control that keeps the phase angle value synchronized with the grid voltage, in addition to an INNER LOOP control capable of varying the inverter's output currents and finally next to the OUTER LOOP control that delivers reference currents to control the active and reactive power to the network, demonstrated the effectiveness of the control strategy proposed in theory.
Aparece en las colecciones: Tesis - Ingeniería Eléctrica

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
T-001533.pdf4,92 MBAdobe PDFVisualizar/Abrir


Este ítem está sujeto a una licencia Creative Commons Licencia Creative Commons Creative Commons